Hampden Data

A ridge, usually of rocks or coral, lying near the surface of the sea, which may be visible at low tide, but is usually covered with water

Data Dictionary for reef_poly: docs.topo.linz.govt.nz/data-dictionary/tdd-class-r...

This layer is a component of the Topo50 map series. The Topo50 map series provides topographic mapping for the New Zealand mainland, Chatham and New Zealand's offshore islands, at 1:50,000 scale.

Further information on Topo50:
www.linz.govt.nz/topography/topo-maps/topo50

An artificial barrier placed in an open channel and over which the water flows

Data Dictionary for weir_cl: docs.topo.linz.govt.nz/data-dictionary/tdd-class-w...

This layer is a component of the Topo50 map series. The Topo50 map series provides topographic mapping for the New Zealand mainland, Chatham and New Zealand's offshore islands, at 1:50,000 scale.

Further information on Topo50:
www.linz.govt.nz/topography/topo-maps/topo50

Industrial cableway; a conveyor system built primarily for the transport of material for industry, power production etc, in which a carrier unit or units run on wire cables strung between supports.

Data Dictionary for cableway_industrial_cl: docs.topo.linz.govt.nz/data-dictionary/tdd-class-c...

This layer is a component of the Topo50 map series. The Topo50 map series provides topographic mapping for the New Zealand mainland, Chatham and New Zealand's offshore islands, at 1:50,000 scale.

Further information on Topo50:
www.linz.govt.nz/topography/topo-maps/topo50

A beacon is a prominent, specially constructed object forming a conspicuous mark as a fixed aid to navigation or for use in hydrographic survey. A cardinal beacon is used in conjunction with the compass to indicate where the mariner may find the best navigable water. It is placed in one of the four quadrants (North, East, South and West), bounded by inter-cardinal bearings from the point marked.

S-57 Object Class: Beacon, cardinal

S-57 Acronym: BCNCAR

This data was compiled for the use in the scale range 1:4,000 to 1:22,000.

THIS DATA DOES NOT REPLACE NAUTICAL CHARTS AND MUST NOT BE USED FOR NAVIGATION.

This data is based on the S-57 data format used in Electronic Navigational Charts (ENCs) published and maintained by the New Zealand Hydrographic Authority at Land Information New Zealand (LINZ). Refer to the following link for information about S-57 data: www.linz.govt.nz/hydro/regulation/

This layer contains the index tiles for LiDAR data from the Canterbury Region captured between November 2016 and January 2017.

• The DEM is available as layer Canterbury LiDAR 1m DEM (2016-2017).

• The DSM is available as layer Canterbury LiDAR 1m DSM (2016-2017).

• The LAS point cloud and vendor project reports are available from OpenTopography.

Lidar was captured for Environment Canterbury Regional Council by AAM New Zealand between November 2016 and January 2017. The datasets were generated by AAM New Zealand and their subcontractors. Data management and distribution is by Land Information New Zealand.

Data comprises:

• DEM: tif or asc tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout

• DSM: tif or asc tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout

• Point cloud: las tiles in NZTM2000 projection, tiled into a 1:2,000 tile layout

Pulse density is 3.44 pulses/square metre.

Vertical accuracy specification is +/- 0.20 m (95%).

Horizontal accuracy specification is +/- 1.00m (95%).

Vertical datum is NZVD2016.

LINZ publishes 1:25,000 scale orthophotos of New Zealand from its archive. The New Zealand orthophotos shown are historical and no further orthophotos of New Zealand will be published.

Coverage of 1 pixel is 2.5m x 2.5m