ANZLIC Metadata Profile: An Australian/New Zealand Profile of AS/NZS ISO 19115:2005, Geographic information - Metadata
Metadata Standard Version
Reference System Info
Reference System Identifier
Waikato - Reporoa and Upper Piako River LiDAR Index Tiles (2019)
This layer contains the Index Tiles for LiDAR data in the Waikato Region covering Reporoa Township and the Upper Piako River captured in 2019.
- The DEM is available as layer [Waikato - Reporoa and Upper Piako River LiDAR 1m DEM (2019)](https://data.linz.govt.nz/layer/104108).
- The DSM is available as layer [Waikato - Reporoa and Upper Piako River LiDAR 1m DSM (2019)](https://data.linz.govt.nz/layer/104113).
- The LAS point cloud and vendor project reports are available from [OpenTopography](https://portal.opentopography.org/datasets?loc=New%20Zealand).
LiDAR was captured for Lincoln Agritech Limited by Aerial Surveys in April 2019. These datasets were generated by Aerial Surveys and their subcontractors. Data management and distribution is by Toitū Te Whenua Land Information New Zealand.
- DEM: tif or asc tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout
- DSM: tif or asc tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout
- Point cloud: las tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout
Pulse density specification is at a minimum of 2 pulses/square metre.
Released by LINZ under Creative Commons Attribution 4.0 New Zealand (CC BY 4.0) with:
Following Attribution: "Sourced from the LINZ Data Service and licensed by Lincoln Agritech Limited, for re-use under CC BY 4.0." For details see: https://www.linz.govt.nz/data/licensing-and-using-data/attributing-elevation-or-aerial-imagery-data
The scan angle is ±20 degrees per the data supplied to us not ±10 degrees referenced in the survey reports.
The LiDAR sensor positioning and orientation (POS) was determined using the collected GPS/IMU datasets and Applanix POSPac software.
Base Station Positions: PP-RTX
The POS data was combined with the LiDAR range files and used to generate LIDAR point clouds in NZTM and ellipsoidal heights. This process was undertaken using Optech LMS LiDAR processing software. The data was checked for completeness of coverage. The relative fit of data in the overlap between strips was also checked.
The height accuracy of the ground classified LiDAR points was checked using open land-cover survey check site data collected by Sounds Surveying Ltd. This was done by calculating height differences statistics between a TIN of the LiDAR ground points and the checkpoints.The standard deviation statistic is 0.030 m; a RMS of 0.033 m and the average difference is 0.012 m. LiDAR is relative to the control check points
The positional accuracy of the LiDAR data has been checked by overlaying Sounds Surveying Ltd surveyed data over the LiDAR data displayed coded by intensity. The data was found to fit well in position.
The point cloud data was then classified withTerraSolid LiDAR processing software into ground and above ground returns using automated routines tailored to the project landcover and terrain.
All product deliverables supplied in terms of NZTM map projection and NZVD2016 height datum.
Classification of the point cloud followed the classification scheme below: 1 - Unclassified 2 - Ground 7 - Noise 12 - Overlap 14 - Above Ground
10 - Rail points were also found in the data not mentioned in the survey report.
Rail (10) and Above_Ground (14) points were reclassified by LINZ as Unassigned classification (1) before providing the classified point cloud data to Open Topography.
Lakes and large rivers were hydroflattened in the Bare Earth Digital Elevation Model.
The deliverables to LINZ were:
1m gridded bare earth digital elevation model (DEM) 1m gridded digital surface model (DSM) Classified point cloud
Copyright of this work is owned by Toitū Te Whenua Land Information New Zealand