ANZLIC Metadata Profile: An Australian/New Zealand Profile of AS/NZS ISO 19115:2005, Geographic information - Metadata
Metadata Standard Version
Reference System Info
Reference System Identifier
Tasman - Tasman South LiDAR 1m DEM (2020-2021)
This layer contains the DEM for LiDAR data for Tasman South and includes Murchison, Glenhope, Motupiko, Howard and surrounding area captured between 2020 and 2021.
- The DSM is available as layer [Tasman - Tasman South LiDAR 1m DSM (2020-2021)](https://data.linz.govt.nz/layer/107836)
- The index tiles are available as layer [Tasman - Tasman South LiDAR Index Tiles (2020-2021)](https://data.linz.govt.nz/layer/107838)
- The LAS point cloud and vendor project reports are available from [OpenTopography](https://portal.opentopography.org/datasets?loc=New%20Zealand)
LiDAR was captured for Tasman District Council by ASL Ltd between 28 January 2020 to 07 May 2021. The dataset was generated by ASL and their subcontractors. Data management and distribution is by Toitū Te Whenua Land Information New Zealand.
- DEM: tif or asc tiles in NZTM2000 projection, tiledinto a 1:1,000 tile layout
- DSM: tif or asc tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout
- Point cloud: las tiles in NZTM2000 projection, tiled into a 1:1,000 tile layout
Pulse density specification is at a minimum of 4 pulses/square metre.
Vertical Accuracy Specification is +/- 0.2m (95%) Horizontal Accuracy Specification is +/- 1.0m (95%)
Released by Toitū Te Whenua Land Information New Zealand under Creative Commons Attribution 4.0 New Zealand (CC BY 4.0) with:
Following Attribution: "Sourced from the LINZ Data Service and licensed by Tasman District Council, for re-use under CC BY 4.0." For details see: https://www.linz.govt.nz/data/licensing-and-using-data/attributing-elevation-or-aerial-imagery-data
Airborne Laser Scanner (ALS) data was acquired from a fixed wing aircraft between between 28 January 2020 to 07 May 2021, using ASL's Optech Galaxy Prime LiDAR system.
- Scanner: Optech Galaxy Prime - Flying height: 2925 m AMGL - Scan angle: 52 degrees - Pulse rate: 400 kHz - Swath overlap: 55% - Swath points per M^2: 4 pts per sq m.
The LiDAR sensor positioning and orientation (POS) was determined using the collected GPS/IMU datasets and Applanix POSPac software.
Base Station Positions: PPRTX
The POS data was combined with the LiDAR range files and used to generate LIDAR point clouds in NZTM and ellipsoidal heights. This process was undertaken using Optech LMS LiDAR processing software. The data was checked for completeness of coverage. The relative fit of data in the overlap between strips was also checked.
The height accuracy of the ground classified LiDAR points was checked using open land-cover survey check site data collected by Sounds Surveying Ltd. This was done by calculating height differences statistics between a TIN of the LiDAR ground points and the checkpoints. The standard deviation statistic is 0.047m; a RMS of0.047m and the average difference is 0m. LiDAR is relative to the control check points.
The positional accuracy of the LiDAR data has been checked by overlaying Sounds Surveying Ltdsurveyed data over the LiDAR data displayed coded by intensity. The data was found to fit well in position.
The point cloud data was then classified with TerraSolid LiDAR processing software into ground and above ground returns using automated routines tailored to the project land cover and terrain.
All product deliverables supplied in terms of NZTM map projection and NZVD2016 vertical datum.
Classification of the point cloud followed the classifications scheme below:
1- Unclassified 2 - Ground 3 - Low Vegetation 4 - Medium Vegetation 5 - High Vegetation 6 - Buildings 7 - Low Noise 9 - Water 18 - High Noise
The Digital Elevation (DEM) was derived using a point to TIN and TIN to Raster process, using a Natural Neighbour interpolation. Hydro flattening was performed as per part 7 of PGF version New Zealand National Aerial Lidar Base Specification Jan 2020.
To improve the accurate representation of bare earth in high alpine environments, some reclassification and manual editing has been applied by Aerial Surveys and LINZ to the DEM. The point cloud data remains as was originally delivered.
The deliverables to LINZ were:
1m gridded bare earth digital elevation model (DEM) 1m gridded digital surface model (DSM) Classified point cloud